Full Manual – Learning
POWERTECH 4.5 & 6.8 L DIESEL ENGINES
COMPONENTS & REPAIR
Introduction, John Deere Dealers, 3/4 Right Rear View, 3/4 Right Front View, AfterCooler, Air Cleaner Operation, Air Filter Restriction Indicator Test, Air Heater, Air Intake and Exhaust System Theory of Operation, Air Intake Pipe, Air Intake System Check, Alternator, Altitude, Effects on Engine Performance, Auxiliary Drive, Balancer Shafts, Bushings and Journals, Measure, Bushings, Remove and Install, Bushing Id, Measure, End Play, Measure, Gears and Thrust Plates, Inspect, Gears, Remove and Install, Install and Time, Remove, Belt Tensioner, Check Spring Tension, Manual Tensioner, Adjust, Remove and Install, Blow-by, Check, Break-in, Engine, Guidelines, Perform Break-in, Break-in, Engine Oil, Camshaft, Bushing Bores, Measure, Bushing, Remove and Install, End Play, Measure, Followers and Bores, Measure, Followers, Inspect, Gear, Remove and Install, Inspect, Inspect and Measure, Install, Lobe Height, Measure, Remove, Thrust Plate Clearance, Measure, Camshaft Followers, Inspect Measure and Assemble Cold Start Advance Switch, Remove and Install, Connecting Rods Bearings, Inspect and Measure, Center-to-center Bores, Measure, Disassemble, General Information, Pin Bore, Clean and Inspect, Pistons and Rods, Assemble, Pistons and Rods, Install, Piston Pin Bushing, Install, Preliminary Checks, Remove, Rod and Cap, Inspect, Torque-turn Cap Screws Coolant, Disposal, Testing, Coolant Heater, Coolant in Oil or Oil in Coolant, Coolant Temperature Above Normal, Coolant Temperature Below Normal, Cooling System, Check, Coolant, Deaeration, Diagnostics Coolant in Oil or Oil in Coolant, Engine Coolant Temperature Above Normal, Engine Coolant Temperature Below Normal, Flush and Service, Pressure Test, Theory, Crankcase Pressure, Check, Cranking Speed Test, Endplay, Check, Failure Analysis, Flange, Clean and Inspect, Front Wear Sleeve and Oil Seal, Gear, Remove and Install, Grinding Guidelines, Grinding Specifications, Inspect, Install, Journals, Measure, Main and Thrust Bearing Inserts, Main Bearings, Check Clearance, Main Bearings, Remove, Main Bearing Caps, Measure, Main Bearing Id, Measure, Pulley, Install, Pulley, Remove, Rear Seal and Sleeve, Handling, Rear Seal and Sleeve, Remove, Remove, Remove and Install Timing Wheel, Replace Front Seal and Wear Sleeve, Thrust Journal and Bearing, Measure, Cylinder Block, Bores, Measure, Complete Disassembly, Inspect and Clean, Main Bearing Bore, Measure, Top Deck, Clean and Inspect, Top Deck, Measure Flatness, Cylinder Head, Cap Screws, Clean and Inspect, Cap Screws, Torque Turn, Check Flatness, Check for Head Gasket Failures, Final Assembly, Gasket Construction and Diagnostics, Gasket, Inspect and Repair, Inspect and Clean, Install, Preliminary Checks, Thickness, Measure, Cylinder Liners, Flange CounterBore Depth, Flange Thickness, Measure, Install Packing and O-rings, Preliminary Checks, Standout (height Above Block), Dealer Fabricated Tools, Coolant System Malfunctions, Coolant in Oil or Oil in Coolant, Engine Coolant Temperature Above, Lubrication System Malfunctions, Engine Oil Pressure High, Engine Oil Pressure Low, Excessive Oil Consumption, Diesel Engine Oil, Diesel Fuel, Dynamometer Test, Engine, Alternative and Synthetic Lubricants, Application Charts, Assembly Sequence, Break-in Guidelines, Break-in Oil, Break-in, Perform, Check for Excessive Tightness, Cleaning, Compression Pressure Test, Coolant Specifications…
- Pages: 513
- Size: 6.98 MB
- Format: PDF (Adobe Reader)
View Manual
MANUAL – JOHN DEERE – POWERTECH – DIESEL ENGINES – REPAIR – ADJUSTMENTS – OPERATION – DIAGNOSTICS – TOOLS – SPECIFICATIONS – SAFETY – SYSTEMS – COMPONENTS – FUELS – LUBRICANTS – COOLANTS – CYLINDERS – PISTONS – BEARINGS – TESTS
